Перегляд за Автор "Shuliak I."

Зараз показуємо 1 - 2 з 2
  • Документ
    Constructing Geometrical Models of Spherical Analogs of the Involute of a Circle and Cycloid
    (Eastern-European Journal of Enterprise Technologies, 2023) Nesvidomin A.; Pylypaka S.; Volina T.; Kalenyk Mykhailo Viktorovych; Shuliak I.; Semirnenko Y.; Tarelnyk N.; Hryshchenko I.; Kholodniak Y.; Sierykh L.; Несвідомін А.; Пилипака С.; Воліна Т.; Каленик Михайло Вікторович; Шуляк І.; Семірненко Ю.; Тарельник Н.; Грищенко І.; Холодняк Ю.; Сєрих Л.
    The common properties of images on a plane and a sphere are considered in the scientific works by scientists-designers of spherical mechanisms. This is due to the fact that the plane and the sphere share common geometric parameters. They include constancy at all points of the Gaussian curve, which has a zero value for a plane and a positive value for a sphere. Figures belonging to them can slide freely on both surfaces. With unlimited growth of the radius of the sphere, its limited section approaches the plane, and the spherical shape transforms into a plane. Thus, a loxodrome that crosses all meridians at a constant angle is transformed into a logarithmic spiral that intersects at a constant angle the radius vectors that come from the pole. The tooth profile of cylindrical gears is outlined by the involute of a circle. A spherical involute is used for the corresponding bevel gears. Other spherical curves are also known, which are analogs of flat ones. The formation of a cycloid and an involute of a circle are associated with the mutual rolling of a line segment with each of these figures. If the segment is fixed and the circle rolls along it, then the point of the circle describes the cycloid. In the case of a stationary circle along which a segment is rolled, the point of the segment will execute the involute. To move to the spherical analogs of these curves, it is necessary to replace the circle with a cone, and the straight line with a plane. The spherical prototype of the cycloid will be the trajectory of the point of the base of the cone, which rolls along the plane, that is, along the sweep of the cone. The sweep of a cone is a sector, the radius of the limiting circle of which is equal to the generating cone. If this sweep, like a section of a plane, is rolled around a fixed cone, when its top coincides with the center of the sector, then the point of the limiting radius of the sector will execute a spherical involute. This paper analytically implements these two motions and reports the parametric equations of the spherical analogs of the circle involute and the cycloid
  • Документ
    Designing a Helical Knife for a Shredding Drum Using a Sweep Surface
    (Eastern-European Journal of Enterprise Technologies, 2024) Pylypaka S.; Hropost V.; Nesvidomin V.; Volina T.; Kalenyk M.; Volokha M.; Zalevska O.; Shuliak I.; Dieniezhnikov Serhii Serhiiovych; Motsak Svitlana Ivanivna; Пилипака С.; Хропост В.; Несвідомін В.; Воліна Т.; Каленик Михайло Вікторович; Волоха М.; Залевська О.; Шуляк І.; Дєнєжніков Сергій Сергійович; Моцак Світлана Іванівна
    The object of this paper is a helical blade in a shredding drum from a sweep surface. Such drums are used in harvesters for crushing plant mass. If the flat blades are installed on the drum, cutting of the plant mass occurs simultaneously along the entire length of the blade. This could cause a pulsating dynamic load. If a flat knife with a straight blade is installed at an angle to the axis of the drum, then the distances from it to the points of the blade will be different, as well as the cutting conditions along the blade. The elliptical shape enables the same distance from the axis of rotation to the points of the blade, but this does not solve the problem. Many short flat knives with a straight blade can be mounted on the drum, placing them in such a way that the time between the individual knives is minimized. However, all these disadvantages can be eliminated by a helical knife with a blade in the form of a helical line. The design of a helical knife from an unfolding helicoid has been considered. In differential geometry, the bending of unfolded surfaces of zero thickness is considered. Bending of the workpiece into a finished product occurs with minimal plastic deformations, the magnitude of which depends on the thickness of the workpiece sheet. The methods of differential geometry of unfolding surfaces were applied to the analytical description of the surface of the helical knife. The parametric equations of the unfolding helicoid were derived according to the given structural parameters of the knife in space and on the plane. That has made it possible to mathematically describe the contour lines that cut the knife from the surface and on its sweep. Formulae for calculating a flat workpiece through the structural parameters of the knife have been derived. Thus, with the specified structural parameters of the knife R=0.25 m, τ=20°, j=65°, according to the resulting formula, we find the radius of the knife blade on a flat workpiece: R0=4.8 m